avatar1338
Forum Replies Created
-
tbh, i would not go down with your long estered test. i would top up with base on days where you are training your lagging body part. its so fast acting, it will be out of your system within hours. i don’t think you will get much out of 50. i would start with 100 if you are using it lets say once or twice a week. if you want to use it before every training session i would stick with 50-75mg.
e-mail: avatarderboss@hotmail.de
-
it depends. i would take your fasted bloodsugar levels and see where you are at. as logn as you are not getting too fat or build a insulin resistance you are gtg imo (esp. if you are “only” running it eod).
e-mail: avatarderboss@hotmail.de
-
as a coach… phil viz is on a totally different level, you can’t even compare them. ive only seen quality info put out by phil. he really knows what hes talking about. in a lot of cases, nick doesn’t but he is a good businessman and knows how to market himself and people trust him because they don’t know better.
i still find his videos entertaining to watch though.e-mail: avatarderboss@hotmail.de
-
i know 🙂 ! it would be pointless anyway to try to replicate all the processes if you don’t have the needed equipment, enviroment or budget to do so.
thx deane-mail: avatarderboss@hotmail.de
-
you made a great point dean and i have to agree in everything you just said. its not just randomly mixing together the compound and carrier oil of your choice… sadly i had to find it out the hard way. in the past, ihad many batches that caused me terrible pip (esp at the beginning) bacause i thought i knew what i was doing. thats why i opened this thread. if people are homebrewing, i want them to learn from my mistakes. since you have a much greater knowledge on the scientific aspects of it i would be quite happy to hear your oppinions on this topics and provide quality information like you did with your previous posts. most of my knowledge is based on talking to pharmacists, other homebrewers and a good amount was trial and error. if i should make a mistake or if i should say something you disagree with, feel free to post your thoughts on it or to correct me if im wrong ????. @drdeanstmart
e-mail: avatarderboss@hotmail.de
-
some of his thought processes are interesting but you have to filter through a lot of bs to get to them. there is usually at least 1 mistake in everything he explaines. his Videos are entertaining but can be dangerous for people who believe everything hes saying. i signed up on his website a while ago and the only positive thing i can report back are some of his training videos.
e-mail: avatarderboss@hotmail.de
-
tbh, idk but i had that shit once and haven’t touched test e since then… that was the only time my stuff was causing me problems.
a few of my friends who homebrewed as well had the same problem so its the compound itself that causes the issue.
if you want to make test, i would recommend that you stick to test cyp and stay away from test e.its not worth it.e-mail: avatarderboss@hotmail.de
-
@doylejlw87
i have always used sterile sartorius minisart 0.2 µm filters but switched to 0.45 µm filters around a year ago.
0.2 µm filters are a pain in the ass to use if youn want to filter more than 10-20 ml. they tend to clog very fast and if you push too hard the can rip quite easily.e-mail: avatarderboss@hotmail.de
-
@doylejlw87
no worries, just let me know if you should have any other questions.e-mail: avatarderboss@hotmail.de
-
@bonacris i have only tested my products. i barely use any ugl stuff anymore.
@doylejlw87
ill share a few links with you where you can see a step by step how its done:
#1: http://www.basskilleronline.com/steroids-converting-powders.shtml
#2: http://www.basskilleronline.com/test-enanthate-notacow.shtml
#3: http://www.basskilleronline.com/steroids-test-enanthate-conversion.shtmlregarding pip.
most people will tell you that the main factor for pip will be high concentrations of solvents (BB) and/or of the bacteriostatic preservative (BA) but i personally say this is a wrong statement. its actually the opposite. obviously BB and BA will cause a slight irritation to the muscle but in most cases, pip is caused by trying to push a high concentration of the chosen drug into 1 ml of oil. the result will be the drug falling out of the solution while its sitting in the muscle. the crystallization will irritate the muscle and will cause the typical symptoms of pip like inflammation, pain and stiffness of the muscle.
so a higher concentration of solvents will actually help to reduce post injection pain as long as you don’t go crazy with them (imo there is no need to go above 28% bb and 5 % ba).a good ratio that will work for most compounds at common dosages would be something between 18 to 22% of benzyl benzoate and 1-4% benzyl alcohol. pip will be minimal to none (depending on the actual compound).
oils:
the choice of your carrier oil will play a major part in this. the higher the viscosity, the less pressure you nned to get the oild through the needle, this can have a direct impact on muscle irritation and will actually reduce pip a lot. every carrier oil will have different properties in terms of how much of the actual drug it can hold. i personally think that the best choices for a moderate to high concentration (for example 300-350 test cyp/e or 100-125 test prop) would be ethyl oleate (which will also act as a solvent and has a very high viscosity), MCT oil ( preferably a mixture of C8 and c10) and GSO (grapeseedoil).
if you want to go really fancy you could use “miglyol 840”. thats imo one of the best carriers you could get but its very hard to obtain and its very expensive.
a mixture of mct and gso or just pure mct oil are my personal favourites.e-mail: avatarderboss@hotmail.de
-
for females, they are a great option (esp. ostarine and s4) because they have basically no andrigenic activity but will promote muscle growth.
for males, mk and gw are very useful (even if both are technically no sarms but most people put them in the same category). gw is great fir imoroving lipids, stamina and to help with fatloss. mk is very useful for increasing appetite, digestion and sleep.
e-mail: avatarderboss@hotmail.de
-
i personally have never tested any raw for heavy metals but i have tested a lot of homemade products for sterility. with ugls, you have to trust your source. if you are homebrewing, thats a factor you can control because you made it.
e-mail: avatarderboss@hotmail.de
-
thats really really interesting Bonacris. great to hear. i have never came across any poor quality raws. basically all of them are spot on. i used to test for melting points but i stopped doing it after a year because all have been 100% correct.
e-mail: avatarderboss@hotmail.de
-
eq takes ages to hit your system because of its long ester. its not worth it imo.
e-mail: avatarderboss@hotmail.de
-
i would take a bit of nolva and get bloodwork done to check your e2 and prolactin levels and adjust your ai accordingly.
e-mail: avatarderboss@hotmail.de