Bonacris
Forum Replies Created
-
For me nandrolon (npp) >> eq
Eq acts like a lighter nandrolon tbh. Less aromatisation, less water retention, no problems with prolactin. But also, mg to mg you have to use more of eq, nandrolon increases my strength much more and eq made my blood too thick also
For me, nandrolon
i agree with but have you tried DHB. That blows NPP out of the water
-
I have tried most of the CBD products on the market and they are useless. My dad has MS and he has come to the same conclusion. However Rick Simpson Oil (RSO) is the real deal. It is extremely concentrated version of the shit that on the market. Very hard to get but there are instructions how to make it online, however it requires a lot of cannabis to make. I personally stick to vaping cannabis at night for the most benefit. But if someone is in prep or on a strict diet the hunger pains can be intense
-
The week before if you lump up from shots but if it doesnt negatively effect your physique I would run it all the way to the bitter end
-
Its a great compound but very hard to find a good source. most labs try to make it too concentrated and it ends up crippling people with the pain or they have to use guacicol to make it stay in solution and that stuff stinks. anything above 100mg/ml is asking for trouble. I make my own and 75mg/ml is a nice sweet spot for daily injections. a little bit of EO to thin it out and it will go through a slin pin.
My experience with it has all been positive. Its like a much stronger primo without the hairloss side (my experience with primo) and like a weaker tren (without the flatness, sweats and mental sides)
-
blacktops are very good. being overdosed they go a long way
-
I found the best sources on meso rx.
-
I made a blend of npp/dhb at 50mg each per ml. painfree and can easily run it through a slin pin. these high dosed DHB formulas are crazy. MAX should be 100mg/ml
-
For my very 1st cycle I used the same 2 pins for 10 weeks. I have also brewed gear for myself and 3 friends and never had any issues. These are not the smartest things to do but just saying someone would want to be very unlucky to get an infection. i dont hear maybe cases at all. Only one i ever heard personally was when a guy dropped his pin and blew it off before using it
-
i always heat my vial. boil water and place the vial in a cup of the boiling water. makes it easier to draw and pin. pinning quads is always asking for trouble. too many nerves in that area. if you pin you glutes and dont have 3 days of PIP then just give up on pinning quads. if your still getting 3 days of PIP then its the gear causing the PIP
-
Huge congrats Corinne. absolutely delighted for you
-
i havent used it myself but i have brewed some for others and its holds easily at 100mg/ml but anything else is pushing it and asking for PIP. even at 100mg/ml anymore than 1ml at a time will have some PIP even if diluted with something else. But none of this is my experience just what i have heard from the guys
-
what causes some of the extreme pip that comes with some test enanthate. From what I have read its carbolic acid or something like that. Its not the usual PIP but golfball sized lumps.
-
New project for Luke seems to be a similar set up to what JP and co are doing here.
Hopefully Luke stays on board here and updates us
Hasnt updated in nearly 2 weeks. I wouldnt hold my breath. Its a pity if it is true, but imitation is the sincerest form of flattery.
-
i personally have never tested any raw for heavy metals but i have tested a lot of homemade products for sterility. with ugls, you have to trust your source. if you are homebrewing, thats a factor you can control because you made it.
what did you find in terms of UGL sterility?
-
I asked my wife about this. Unless you’re using USP grade oils and powders and the medication created within an actual pharmaceutical laboratory then non of it is technically sterile in the eyes of medicine. My biggest concern with UGL powders is the heavy metals and containment’s in it. Of course many UGL gear is safe to use but non of it is properly sterile in a laboratory sense. Those filters that you would put the oil through does not remove heavy metals and other potential issues.
Jano used to test for heavy metals but doesnt any more as he said he never once found traces in any raw he tested. i have sent out numerous samples for testing and all except tren ace came back above 98%. tren ace was 96%